For Use On:

Vinyl Tile Flooring (see spec sheet for more surfaces)

Description:

A new generation, high gloss, user-friendly floor finish specially formulated for daily Ultra-High-Speed (UHS) burnishing. The metal-interlocked, acrylic-copolymer floor finish provides outstanding Ultra-High-Speed (UHS) burnish response and unsurpassed “wet look” gloss. It is ideally suited for a wide range of applications in the retail market and other areas where frequent daily Ultra-High-Speed (UHS) burnish maintenance is done.

Directions:

Finishing: Apply 3 or 4 liberal coats of finish using a clean mop. Allow a minimum of 30 minutes drying time between coats. Apply additional coat to obtain desired gloss.

Burnishing: Dust mop or sweep thoroughly. Clean floor with a neutral floor cleaner diluted according to directions. Burnish using the appropriate pads.

For Use On:

Terazzo, Flagstone, Quarry Tile, Brick and Concrete

Description:

A high performance premium quality acrylic membrane coating for sealing and finishing non-resilient hard surfaces. This waterbased coating should be used where demand for excellent adhesion, chemical resistance, and wear is required. Fast drying, with no solvent fumes, this product is ideal for use in enclosed areas. This product should be used for interior applications only.

Directions:

Remove all grease, oil, and other foreign material by scrubbing with a heavy-duty cleaner and good scrub brushes. For better adhesion on permanent type coatings such as moisture-cured urethanes or epoxies, it is recommended that the surface be abraded with a 100-mesh screen disk. Smooth, dense concrete surfaces should be acid conditioned before application. When finished, rinse floor thoroughly with clear water and allow to dry.

Apply a liberal coat using a mop, squeegee, roller, lambs wool applicator or other appropriate applicator. If higher gloss is desired apply a second coat after allowing first coat to dry approximately 45 minutes. Surface temperature should be above 40F. Allow final coat to dry at least 8 hours before allowing heavy traffic onto floor.

For Use On:

Vinyl Tile Flooring (see spec sheet for more surfaces)

Description:

A new generation floor finish stripper that rapidly penetrates and solubilizes floor finish. Powerful solvents combined with penetrating amines dissolve the finish on contact, reducing the waiting periods for removal of the finish. This product completely evaporates from the surface. Can be used with or without a floor machine.

Directions:

Dilute in cold or mildly warm water.  Mop on to floor in smallish sections, mopping back over the solution to agitate the stripper.  Run over the solution with a propane stripping machine, autoscrubber, or continue to mop.

Remove solution and old finish with a vacuuming device and allow the floor to dry completely. If desired, a deep rinsing step can be added. Apply new finish per manufacturer recommendation.

For Use On:

Vinyl Tile Flooring (see spec sheet for more surfaces)

Description:

Armadillo’s Ultra 25 is a high solids, high gloss floor finish that responds well to periodic buffing and has considerable resistance against wear.

Directions:

After stripping the floor, rinse very well.  Pour Ultra 25 into a lined bucket and apply with a rayon mop or dustmop.

Allow to dry.  Repeat two or three times as conditions dictate.

For Use On:

Vinyl Tile; Restoring terrazzo and other hard surfaces

Description:

We sell well regarded propane strip machines such as the Aztec Sidewinder and the Onyx Terminator Tri-Strip.  Please visit the “Contact” page (in the upper right hand corner) for more information, up-to-the minute pricing and a realtime freight quote.

Directions:

Strip 15,000 square feet per hour or scrub 30,000 square feet per hour.  The three brush head counter-rotational setup, combined with the machines weight provides superior stripping/scrubbing capability without the side-torque of single pad setups.

For Use On:

Vinyl Tile, Concrete and other hard flooring surfaces

Description:

We sell fine autoscrubbers such as the Advance Warrior and the BOOST Autoscrubber with industry first orbital technology.  Please visit the “Contact” page (in the upper right hand corner) for more information, up-to-the minute pricing and a realtime freight quote.

Directions:

Wet scrub with an integrated dry vaccuum.  Choose from a dual rotational brush setup or the BOOST’s rectangular pad with orbital motion (capable of stripping without stripper.

Battery technology ensures quiet portability.

For Use On:

Vinyl Tile Flooring

Description:

We sell fine machines such as the Aztec Reliant and the Onyx Black Diamond burnisher, each outfitted with a Honda or Kawasaki motor.  Please visit the “Contact” page (upper-right hand corner) for more information, up-to-the minute pricing and a realtime freight quote.

Directions:

For use in dry buffing application with a variety of pad coarsities.  Propane buff machines may be also used with products such as Armadillo’s Anti-Slip & Gloss restorer – cleaning and repairing while bringing back a brilliant shine.